- 您现在的位置：买卖IC网 > Sheet目录250 > SD24C.TCT (Semtech)IC TVS BI-DIR 24V 350W SOD-323
SD05C through SD24C
PROTECTION PRODUCTS
Applications Information
Device Connection Options
The SDxxC TVS diodes are designed to protect one
data, I/O, or power supply line. The device is designed
to replace multi-layer varistors (MLVs) in portable
applications. It is easily implemented on existing 0805
MLV pads and is only slightly larger than 0603 MLV
pads. The device is bidirectional and may be used on
lines where the signal polarity is above and below
ground. The device is symmetrical, so there is no
cathode band.
Circuit Board Layout Recommendations for Suppres-
sion of ESD.
Good circuit board layout is critical for the suppression
of fast rise-time transients such as ESD. The following
guidelines are recommended (Refer to application note
SI99-01 for more detailed information):
Place the TVS near the input terminals or
connectors to restrict transient coupling.
Minimize the path length between the TVS and
PRELIMINARY
Device Schematic and Pin Configuration
Size Comparison to 0805 MLV
the protected line.
The ESD transient return path to ground should
be kept as short as possible.
Place a TVS and decoupling capacitor between
SOD-323
Note: Nominal dimensions in inches
0805 MLV
power and ground of components that may be
vulnerable to electrostatic discharges to the
ground plane.
Minimize all conductive loops including power
and ground loops.
Use multilayer boards when possible.
Minimize interconnecting line lengths
Never run critical signals near board edges.
Fill unused portions of the PCB with ground
plane.
Component Placement Comparison
Matte Tin Lead Finish
0805 MLV on
0805 Solder Pad
SOD-323 on 0805
MLV Pad
SOD-323 on Recommended
(SOD-323) Solder Pad
Matte tin has become the industry standard lead-free
replacement for SnPb lead finishes. A matte tin finish
is composed of 100% tin solder with large grains.
Since the solder volume on the leads is small com-
pared to the solder paste volume that is placed on the
land pattern of the PCB, the reflow profile will be
determined by the requirements of the solder paste.
Therefore, these devices are compatible with both
lead-free and SnPb assembly techniques. In addition,
unlike other lead-free compositions, matte tin does not
have any added alloys that can cause degradation of
the solder joint.
? 2004 Semtech Corp.
5
www.semtech.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SDA004-7
DIODE SW 200MW 80V ESD SOT363
SDC15.TCT
IC TVS BI-DIR 12V 300W SOT-23
SDN01G64D1BE2HY-60WR
DRAM DDR1 1GB 200-SODIMM
SDN03264C1CE1HY-60WR
DRAM DDR1 256MB 200-SODIMM
SE120FML,OR
CASE 8.7X7.45X3.89 ORANGE W/LOCK
SE1220FML,GM
CASE 28.17X22.27X15 GM W/LOCK
SE300FML,OR
CASE 10.80X9.85X4.87 ORANGE/LOCK
SE520FML,OR
CASE 14.85X12.15X6.85 ORG W/FOAM
相关代理商/技术参数
SD24CTC
制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Single Line TVS Diode for ESD Protection in Portable Electronics
SD24CTG
制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Single Line TVS Diode for ESD Protection in Portable Electronics
SD24D25-06
制造商:Teledyne Industrial 功能描述:Relay SSR 制造商:Teledyne Relays 功能描述:SOLID STATE RELAY
SD24D40-06
功能描述:固态继电器-工业安装 40A 12-280VAC Zero Cross Faston
RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel
SD24D40-06/R
制造商:Teledyne Relays 功能描述:RELAY SSR 3MA 30V DC-IN 40A 280V AC-OUT 8-PIN - Bulk 制造商:Teledyne Relays 功能描述:SOLID STATE RELAY
SD24D50-06
功能描述:固态继电器-工业安装 50A 12-280VAC Zero Cross Faston
RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel
SD24D50-06/R
制造商:Teledyne Relays 功能描述:RELAY SSR 3MA 30V DC-IN 50A 280V AC-OUT 8-PIN - Bulk 制造商:Teledyne Relays 功能描述:SOLID STATE RELAY
SD24K5
制造商:Comair Rotron 功能描述:DC Fan